Printable View
Has anyone had any experience or does anyone think that a touch up spray gun will work with shellac and vice versa, taking for granted that the shellac is properly put through a strainer to weed out any undisolved shellac to prevent clogs.
Cheers
Peter
HMMmm! atomised metho around a sparky compressor in a shed full of electrical equipment, yep that's a good idea! can I watch!................. at a distance of course!!!
NO you cant watch, was planning on keeping the compressor insinde and spraying outside as I usually do. So any real advice.Quote:
Originally Posted by Dave50
I asked the same question a long time ago here as I wanted to refinish seven silky oak chairs with shellac and thought spraying maybe the way to go (HVLP spray unit). Major draw back with what I wanted to do was overspray and of course as already pointed out atomized metho. In the end I applied by brush for the first couple of coats rubbed back and then used a rubber ? (cotton cloth with cotton wool inside) to apply the shellac. Am really happy with the result and have to say it was very therapeutic.
Maybe it's a case of what are you finishing??
OK.. ADMIN intervention here.
The OP (castaway) asked a "method" question.
We don't know his shed setup........so lets just look at the method.
I.E...can you spray shellac.
Have used the same method on previous projects as well to great success. I have a new project that I thought would be better suited to spraying it on. Having problems with the shellac drying too fast as I'm having to go around cut outs and curves. I might try to brush it on again. But I'm going to give the spray gun a go and see what the results are. What other advice did you get when you first ask this question.Quote:
Originally Posted by Sapling
Cheers
Peter
From memory that was about it. The over spray was the point that put me off as the chairs are quite fine and as there were so many angles that I would have had to point the spray gun, over spray would have also affected other parts of the chairs! And i'm no spray painter.
I'll do a search for the thread.
Intresting question - I for one could see no reason that it could not be done, though one would need to get the viscosity and air presure right.Quote:
Originally Posted by Castaway
I think that you would need to use more metho than a normal mix as the most will evaporate from spraying before the shellac hits the surface.
I would be intrested to hear the results.if some one has tried it.
Cheers Warren.
:whs:
Watch this get "flamed" :hahaha:
Anybody heard of airbrushes????
No wonder I didn't remember much about it, was three years ago.
https://www.woodworkforums.com/f9/noz...shellac-49015/
Hey Warren hows it going. Any new radios lately. Had a look at that phillips again and still could not get a model number. Yeah this project is a small Airzone Cub and was having trouble with the shellac in places. Well I just bought a spray gun online tonight so I will experiment and let you know.Quote:
Originally Posted by Wood en I
Just had a look... interesting. Now I would of thought that you needed to decrease the amount of metho to make the mix a bit thicker to prevent evoporation.Quote:
Originally Posted by Sapling
Hi Peter. I think that if you used a thicker shellac you will require a higher air pressure and the metho loss from spraying could leave a thick coat that may not dry so easy.Quote:
Originally Posted by Castaway
I would use low pressure around 25 psi perhaps even lower to keep the evaporation down.and add a little extra metho as you do not want the spray to be dusty, but I am only guessing and perhaps your idea is correct,
As soon as I read your post I guessed that it may be a timber radio cabinet with lots of little areas hard to get at,Quote:
Originally Posted by Castaway
Peter on your philips radio you would have had a sticker with all the radio details on the rear panel I would guess that it has fallen off years ago.
And yes I have purchased another radio a HMV chassis with a smashed Plastic case but I only want it for parts to restore some other HMV radios that I have, also purchased another valve tester - a ( Paton VCT ) I hope to restore this one to working order,
Cheers
Yeah the back is missing of it so no sticker. Was hoping there was another on the chassis but no luck. Check your PM sent you a link to some radio stuff.Quote:
Originally Posted by Wood en I
I'm a newby when it comes to spray painting and I'm still learning. The situation is almost desperate enough for me to read the instructions BUT I look at it this way. When I can find them, I buy Zinsser spray cans of shellac. If you can buy spray cans you must be able to spray it yourself? I know there must be complications re nozzle size vs thinning agent vs HVLP etc but it must be possible. The other alternative is to buy Zinsser spray cans?Quote:
Originally Posted by watson
I got my last one at Anagotes but I don't think they carry it anymore...
fletty
Fletty any time you want to borrow the spray gun let me know.
https://www.woodworkforums.com/f9/noz...shellac-49015/
A Perfect Finish
Fletty, I should have my spray gun next week. Will be posting results of it, hopefully with some good news.Quote:
Originally Posted by fletty
Peter
I have never seen or heard of Zinsser shellac spray cans. I wonder what they use with the shellac I doubt that it would be Metho onlyQuote:
Originally Posted by fletty
A little off topic/only partially related - Hard Shellac sprays nicely when thinned, so I am told
Excellent news...Quote:
Originally Posted by Elill
http://www.zinsser.com.au/downloads/...ellac_Info.pdf Product Info sheet.
Rust-Oleum / Zinsser Asia Pacific | History Zinsser Australia website which might be of help when finding a supplier.