Another one in the club. Its amazing how quickly it happens. Good luck Ironwood. I'll teach you some tricks to freak out the grandkids....
Printable View
Another one in the club. Its amazing how quickly it happens. Good luck Ironwood. I'll teach you some tricks to freak out the grandkids....
:rofl: I have only read the first post in fear of there actually being pictures! :rolleyes: At least you have an excuse for the typos for a while! Hope things go well! :UQuote:
Originally Posted by Ironwood
I too had to scroll past fast! Yuuuuuuuuuuuuuuuuuuuuuuuuuuuuuuuuck! I'm not even gonna read about it! :C:rolleyes:Quote:
Originally Posted by Fuzzie
Ouch, Hope it heals up real quick.
Sorry to dissapoint with no photos TL :D.Quote:
Originally Posted by tea lady
I only use 2 fingers to type normally, so it hasnt slowed me down too much :-.
Went to the Doc for a checkup on Monday, looks OK so far. Booked in to get the stitches out on Friday morning.
I can almost feel the pain. Hope it heals quickly. Take it easy.:2tsup:
Thanks John.Quote:
Originally Posted by munruben
It only hurts when I bump it :C, and thats quite often trying to do my job:(
Ironwood and EVERYONE please note:
UVEX Bamboo gloves with a cut proof rating of 5 are FAB-U-LARSE. You lose minimum dexterity, they are exceptionally comfortable, and come in five different finishes (no non-slip coating through to full non-slip coating). They last for ages and cost around eighteen bucks. When my current pair finally wear out I'm going to test them in a few different ways (knives, scissors, axe etc) and will post some pics. That could be a while though - they look like crap now, but don't show any signs of expiring (and that's with 2-3 hours a day, every day, for the last eight months).
Only yesterday my dopey left forefinger bumped into a savagely sharp Miebach BP drill spinning at about 1200 rpm, and whilst it gave me a belt of adrenalin :o, I hardly felt anything - just a bit of vibration. Granted that it wouldn't have done a lot of damage without the gloves, but there certainly would have been blood. I even use one on my left hand whilst hand planing (I'm right handed) to save against a cut from the timber edge, and I've been saved a few times.
I use these gloves for many many tasks and they just don't interfere. Available from Blackwoods and others.
Looky hear Profas COM EN
What's more, they are made in Germany - nuff said?
UVEX also make a whole host of other safety equipment, and I'm particularly interested in getting a helmet and perhaps a baseball cap.
Regards, Brett
I'd be very, very careful about using any gloves around anything spinning at any decent rpm. The only spinning power tools I use with gloves are angle grinders and a chainsaws and that's because I never put my hands anywhere near the spinny bits.Quote:
Originally Posted by FenceFurniture
Besides they wouldn't help a jot against a set of jointer blades.
Hi Bob, is that because the gloves (and fingers) could be drawn in? It's a tough choice eh?
I wonder what the OH&S eggspurts have to say on this matter.
YepQuote:
Originally Posted by FenceFurniture
I think it's a no brainer, I rather get a cut or even a finger taken off than to get all the flesh stripped off my hand or arm - these are horrendous injuries.Quote:
It's a tough choice eh?
Generally it's no gloves near rotating shafts. These days rotating shafts have to be guarded so you can't even get your hand near the rotating piece - in that case the risk from gloves is much reduced and some form of glove then becomes a requirement. That's fine since they generally reduce cuts and scratches at some minor loss of dexterity.Quote:
I wonder what the OH&S eggspurts have to say on this matter.
I so use gloves in my shed and work place quite a bit. Welding gloves, thin leather ones for Chainsaw and angle grinder work, Just doing a bit of greasy mechanical maintenance when there's no mechanical motion I'll often slip on a pair of latex gloves. Their also good for painting. If I did a lot of mechanical work or even metal work I'd probably go for something like the uvex. But lathe, mill, drill press, and power tools I'll stick with bare hands.
Welcome to the club left thumb 1st joint lost years ago while in stupor after nervous breakdown of my brother.
Thanks, but its a club I never wanted to join :-.Quote:
Originally Posted by acmegridley
Went and got the stitches out today, a little bit of infection setting in on the wound.
Going back on monday for another checkup.
Hoping it doesnt get worse, or I may have to get a bit more chopped off :(.
(after the shuddering, shivering and mental imagery stop)
I hope the infection doesn't set in!
I shuddered every time I heard my dad start up his power tools. He's extra careful but the thought would always play through my head and scared me. What'm I going to do with myself when I finally move in with Skew eh? I'll have to start taking paramedic and advanced emergency response courses just to assuage my own unnecessary fears.
I'll keep my fingers crossed for you Ironwood.
Let us know how you are, please.
The best precautionary measure would be to just stand behind Skew. :DQuote:
Originally Posted by Skew's_Girl