Iain, just out of curiosity is the Waterford signed?Quote:
Originally Posted by Iain
I havent come across any as yet, and I am just wondering.
Al :)
Printable View
Iain, just out of curiosity is the Waterford signed?Quote:
Originally Posted by Iain
I havent come across any as yet, and I am just wondering.
Al :)
The problem with mechanical meens.Quote:
Originally Posted by Groggy
There may be stress in the object which will be released with vibration, the results are final. :eek:
Heat may also make the stress fracture.
I have an Uranium float bowl centre pice from the 1930-50's.
I bought it knowing it had a damaged base.
No worry thinks I.
Glass sheet, grits, water, hand action only. :rolleyes:
I ground about 3mm off the base to make it level so it would sit nice.
Beautifull,I wouldnt sell her for any ammount of money.
I place her under a UV light to excite the Uranium in her.
She glows the most beautiful green you have ever seen..
Two days later I hear.....click.......
My beatiful Godess had cracked.......:eek:
The UV light produced enough vibration to make stresses in the glass fracture. :mad:
I was devistated.
But I still love her.
You can see the crack in the bottom right.
Al :(
Al, I was surprised to see your goddess's crack in that photo, you must've been appalled to hear it split like that! :eek:
(ahem)
Originally I was thinking that a 'hard' machine-driven grinding piece on a mandrel may set up a harmonic frequency that would cause the glass to shatter. Later on it occured to me that a felt wheel would not impart vibration to the glass as easily and would in all probability dampen it somewhat. In retrospect you are right, fine crystal should most probably be done by hand unless you have some experience at it.
I was, I havent seen a Godess so big before.Quote:
Originally Posted by Groggy
She is about 12" tall, most others are only about 6" tall.
Maybe she is the Amazon Queen??
Al :D
I will send some grit tomorrow.Quote:
Originally Posted by Knurl
I will send 220 and 600 grit, and some polish.
The rules are the same as woodwork, start with the courses grit 220, then work your way down the grits, removing the previous grit scratch marks.
The polish is rated at 100,000 grit. :p
Al :)
Why go to all that trouble. just use some clear west system epoxy and smooth it over with the 600 grit and polish:)
My Waterford, isn't signed. Just has a watermark (sic) saying Waterford under the base.
I have a reasonable amount of Stuart Crystal not Waterford, I put the two on an even level given the quality of the crystal hence my comments.Quote:
Originally Posted by ozwinner
I had Stuart Crystal make a replacement sherry glass for me.
I have not had anything to do with Waterford and know nothing of signatures but my parents were friends of the Stuart manufacturers in England and had a lot of one off pieces made as gifts which I have inherited.
The Stuart pieces bear a hallmark (on the underside of the base) and some a signature if they are special enough to warrant it.
I've just received the grit and polishing powder, thank you very much.
When you say add water and detergent, in what ratio? Does it matter and do you need water and detergent or can you get away with just detergent?
In one of your posts Ozwinner you say apply with a cloth. Doesn't that heat up the glass and possibly scratch more than a 200 grade grit will do? I was thinking dipping my index finger in the solution and rubbing it on the chip.
I can see myself rubbing the chip for a few minutes then washing the solution away and inspecting the chip under magnification.
I'm very patient but with a house full of guests this weekend I'm not going to get the time to start this before next week. I'll post results so everyone can see the results.
Hopefully I won't have pictures like the Goddess.
No problem.:)Quote:
Originally Posted by Knurl
The detergent is only to break the suface of the water.Quote:
Originally Posted by Knurl
As long as the grit is wet/damp.
Always use grits wet or damp, a grit, is a girt, is a grit, damp or dry it will still scratch the grit size.Quote:
Originally Posted by Knurl
Although when silicon carbide breaks down it still retains the crystal shape, only smaller.
Cool. :cool:Quote:
Originally Posted by Knurl
Its always hard to tell if there are any stress fractures inside.Quote:
Originally Posted by Knurl
My Goddess was dropped by the previous owner, quite hard too.
Good luck.
Al :)
Well after 2 months I finally found the 12 hours to work on my lead-crystal glass. Started with Ozwinner's 220 grit in green Palmolive dishwasher solution - less Palmolive more grit! Using an old rag i spent 1 hr patiently working on the chip to no avail. Everything seemed as sharp as ever. I then get out the trusty Dremel and put on a felt pad and soaked it in the Palmolive ("you're soaking in it!"). Very messy business because teh Dremel puts more on the walls of teh shed than on the glass. Discovered that I could use the flat face of the pad and the grit stayed in place.
But still no effect. So I checked out the other wet&dry disks in the Dremel kit and found one that "felt" fine-ish and is marked "XXX" so in it went! Immediate results - I could quickly and carefully grind down the sharp edges and generally smooth out the line of the lip.
I'm thinking that XXX was needed fro Lead Crystal before 220 or 600 (from Ozwinner with thanks) because now I had plenty of places where teh glass had become abraded and the fine grits made some little impact on the surface. I'm thinking I need to try again with 180 to 200 grit before going back to the 220 then 600.
All in all the building foreman looked at it with her discerning eye and said that yes it was now smooth but she wants to cut the lip down right around its circumference. Oh well....I learned something didn't I?