You could flog the entire surface very thoroughly with a length of heavy chain :)
Make it an antique.....speeding up the kids job :)
Seriously, a quick sand and steam out the dents.
Printable View
You could flog the entire surface very thoroughly with a length of heavy chain :)
Make it an antique.....speeding up the kids job :)
Seriously, a quick sand and steam out the dents.
Not trying to be a smart aleck here, but, had the same problem on a desk built for student son in the days of black and white.
They only solution I finally came up with was, another refinish, polish and covered with safety glass. Yes, the glass was expensive, but the finish has remained like a new store bought one. No scratches, dings or biro impressions, once in a while wipe over with a damp cloth and back to square one. 30+ years on and counting.
Hey mate, there are others here more expert than me but here's my penny's worth. If you use polyurethane, 24 hrs is nowhere near long enough to cure it. 7 days minimum per coat with a light sand between coats with 240grit and wipe down with a tack cloth to get the surface dustfree for the next coat. Use new poly not old stuff that's been sitting around growing a thick skin on top. Mind you, polyurethane on Blackwood is sacrilege. 😲
Poly is a soft, flexible plastic coating, microns thick. It can't offer diddly squat for mechanical protection.
To keep the table looking like it's never been used, I'd suggest 1/8" Plexiglas = methacrylate sheet.
Off at Uni, I missed my kids. The dinged up table kept them with me.
I don't think it would help with dents but you can get self repairing clear coat for cars, is there anything similar for timber?
I agree with the Shedmeister,Quote:
Originally Posted by Shedhand
Blackwood under plastic is a sin. Seems to me that the easiest method of saving your table from more damage is to do what most have suggested by way of stripping the table and refinishing (after steaming). But I would refinish the table using a robust oil finish such as Organoil Hard burnishing Oil. Then I'd go and buy a couple of robust plastic desk protection pads to use over the top for the kids to use.
Alternatively, rather than plasticize the table, buy a plastic table for the kids to use. And there's always keeping the table like it is now and savoring the memories of this time in your later age. This should not be underestimated.
Regards,
Rob
we keep comming back to the issue that the timber is soft and that is what is being indented ....... unless you run a very very thick hard coating you will not solve your problem.
By far the best comp[omise is to refinish the top then get a sheet of glass cut to size and put that over the table top till the kids leave home.
cheers
Or teach them to put something under the paper, writing on something soft is horrible anyway.
Lovely Blackwood table Tony. I wouldn't put a cover on it either.
When I made my dining table I used a two part Intergrain finish. It is like a thin layer of glass. Shiny and hard. I didn't want to put any cover over the timber.
After nearly twenty years it still looks good apart from a ding from a heavy casserole dish and a candle burn spot.
I can't complain about how tough it is.
But I really don't like the thick glossy finish.
Now I finish dining tables with Kunos Oil. I go for a satin/low sheen finish. I can still feel the timber.
General marks wash off no problem and a wipe over with more oil maybe once a year keeps it looking great.
Your pens and pencils will still make indentations but the stains will wipe off.
A temporary cover might work but it is a shame the kids wouldn't get to work on the nice timber.
Blackwood is reasonably hard so you aren't going to end up with it looking like and old workbench.
My preference would be to clean off the marks as well as you can and give it a coat of Kunos oil or similar. Re do this when you think it needs it. keep enjoying the the look and feel of the beautiful Blackwood.
When the kids leave home you might sand out the grafitti and re-oil or just re-oil and enjoy the history.