Wood working or timber quiz 06/05/04

Good morning Mates,
If you have a log that is 60.95 centimetres in diameter at the small end and 4.8M long.

Approximately how many board feet of lumber are in that log?

Respectfully, ;)

we're in June already ....... did i oversleep?

hmm .... metric log, board feet ..... this could be interesting. Mind you I'm with you Ralph .... metric doesn't come naturally to me either.

Sorry Ralph I have no idea.

We don't do "board feet of lumber" over here, but rather cubic metres of timber.

Craig

About 400 - 425 depending on which formula you use.

Quote:

---

we're in June already ....... did i oversleep?

---

Jackiew

this is the american way of presenting the date. Month, day, year.

Quote:

---

Originally posted by PaulS
Jackiew

this is the american way of presenting the date. Month, day, year.

---

methinks jackiew's reference was said in jest....

the internationally standardised date format is...

YYYY-MM-DD

If everyone uses this there isn't a problem...

Ralph are you happy to use this format to avoid any further confusion?

Good Afternoon Mates,
I have so much to learn about your ways in the land of OZ but, I am enjoying learning as I go and yes, I think when in Rome do as the Romans do and the same holds true for OZ. From this point on I will date all matter by the YY/MM/DD.
Now for the answer to the quiz, since I did not know that you blokes figured in cubic portions of wood, I will explain how we do it up here if nothing else for your information.

A log that is 16' long and 24" in diameter at the small end, you must first remove one inch from each side of the log to remove the bark. So 24 - 4 = 20" now decide that by 4 and you have 5. Now square that number for a total of 25 x 16' = 400 BF of lumber. Depending on the saw kerf, this could be even less but
the 400 board feet is an approximate figure.

Hope this explains a little of our culture to you folks.

Thank you for your support of these quizzes.

Respectfully, ;)

Hey Ralph,
About the date thingy,
Why not give the month its name instead of a number, that way anyone knows
May 6 2004
6 May 2004
2004 6 May
2004 May 6
all means the same.

And getting rid of numerals helps those woodworkers who have not got 12 fingers to count up the months on.

Never mind woodies who haven't got 12 fingers,what about the woodies who haven't even got the normal 10?

He must have been thinking about the Tasmanians.

(Duck and cover)

I can count to 31 on one hand and 1023 on two and I've never even been to Tasmania ;)

Quote:

---

Originally posted by silentC
I can count to 31 on one hand and 1023 on two and I've never even been to Tasmania ;)

---

Use your toes too.. then you'll get to 1048575... Now that's a lot of board feet... ;)

Hello Friends in the land of OZ,
Since you blokes have or don't have enough fingers and toes for counting the months and to try to make the dates simple I will take the advise and go with day month (spelled out) and year.

Example 6 May 04 or should I install the 20 before the 04 to keep everyone in the same century?

Respectfully, :)

SilentC, I thought I was the only one who used binary notation on my fingers. Hmmm...is that binary digital?

Can't remember when I started doing it or where i learned, must have been high school, early 60s. Was my party trick for a while.

Alex,

I used to program in Assembler and it became second nature.

I find 8 a very difficult number to represent. For some reason, I have no problem with 4. ;)

Tonz, I find it hard to represent anything other than high or low values with my toes, can you recommend any exercises?