Cutting and sanding glass - dummy alert!

Hey all,

When I eventually work out the best way to cut the wood, :? I intend building a few small reptile enclosures. The doors are going to be sliding glass in the 4 or 5mm plastic track that you can buy at Bunnings. I have so many bits a pieces of glass lying around it seems silly to buy some - but my 2 questions are:

1. Is using one of those cheap glass cutters to score the glass and snap it down the score line accurate, or does one get cr*ppy edges etc?

2. Whats the best way to get a smooth, rounded edge on the exposed ends of the glass, rather than the sharp cut edge? Or can this only be done by the pros?

Since glass tends to be expensive, yet theres so much of it around that noone wants (including old fish tanks), seems like theres a bit of dough to be saved.

Thanks
Martin

Use silicon carbide paper, (its the black paper,) it will take the edge of glass no worries.
Start with something like 240 grit, and if you want it smoother progress to 480 grit.

Just do it by hand with a longish sheet and roll the sheet over the edge a coupla times.

Al :)

Yes you can cut accurately with a glass cutter but there's definite knack to doing it and you wont pick it up quickly. Practice on some offcuts first.

Arrising or rounding is done on a machine. You can simulate an arrised edge using a block of carborundum or sandpaper but you wont get a nice clean edge this way. If it's for show, you really need to get a glazier to do it for you. It might be worth taking your cut sheets in to see if they will arris them for you if you can find someone who'll do it.

I once built a machine using a beltsander but it was only marginally better than doing it by hand. I mainly used it when people wanted the edge taken off but it wasn't for show.

The glass cutter to go for, I can speak on this as I cut glass all the time for picture frames is the one with the oil inside it and a cutting wheel at the end.

Use a straight edge to go along the edge and start the wheel on the glass. You will hear a scratching sort of noise if you are using enough pressure.

When you "break" the glass you can do small pieces just in your hands by holding each side and bending it a touch. Larger pieces it's best to put a bit of wood or something straight under the glass and lay it down on the wood

Studley

I'm just about to do some myself and did a google to learn the tricks.
Studleys nailed it - well from what I've read. also just one score don't go over vthe line repeatedly.
Silents advice was also offered - get some scrap and practice.
I'll let you know how I go... I'm building the boys an ant farm..Yeeehaaa.

Quote:

---

Originally Posted by Bleedin Thumb

I'll let you know how I go... I'm building the boys an ant farm..Yeeehaaa.

---

Better get some Aloe Vera in, Im sure your boys will itch with ants on them..

Al :o

G'day,
My only input...being a glass miser.......is that glass gathers dust/bird crap/all sorts of stuff. After cutting several bad bits I learned that if you clean the glass first, then follow all the advice the forum just supplied, you'll get good straight edges, If my missus wants her Enjo stuff back I'm buggered.
But squeaky clean glass cuts good! or well, or some other word!!

Regards,
Noel

Quote:

---

Originally Posted by watson

But squeaky clean glass cuts good! or well, or some other word!!

Regards,
Noel

---

Gooder?

Al :2tsup:

Indubitably!
Clean glass gives good cuttage!
Regards,
Noel

Even pressures the trick when ever cutting glass, simply because glass doesn't like to bend. ....so think about a good flat table....

Score the line running the glass cutter along the wood.....helps to clamp the wood to the glass with padded clamps, so it won't slide on ya....can concentrate on making a good score better.

I'd use a straight wooden edge under the score line regardless of how thick the glass is........put even pressure on the piece your bending over with another piece of wood under your hand.......It should just click right off real quick......3-4mm glass a piece of cake, which sounds like all you'll need.

Try and make the score with just one pass from edge to edge....if the scores not complete (which is easy to do). ...especially near the ends.....well it won't break straight

Definetly practise on scrap first like said.....don't expect to pull it off first time....but its easily learn't.

Hi Martin, Get your self a diamond sharpening block from one of the tool markets about $10/15.00 they come in a wooden box and take the edge off glass with ease....Peter

Thanks for the responses guys. Much appreciated.

I will take them onboard, and let you know how I go.

Martin

For a really smooth rounded edge (smooth as glass, one might say), I think the pros use what's called "fire polishing." I don't know what kind of flame or torch they use, and I haven't had the nerve to try it myself.

Joe

With the cheap wheeled ones you have to put quite a firm pressure on to ensure an unbroken score line, so the break doesn't wander. If it does wander a bit, then you can nibble away the excess with the jaws on the cutter. They go blunt fairly quickly, and they can rust, but that's not an issue if you've only got a few panes to cut. Follow Bleedin Thumb's advice and don't try to go over a line again or it will kill the blade straight away.
I've seen the pros use non rotating, diamond tipped cutters, and you may be able to pick up one of the lesser quality ones quite cheaply. You won't need nearly as much pressure for an unbroken score line and you'd notice the difference straight away if you've used both. There's less chance of the break wandering, and they last heaps longer.
You could probably take your glass to a glazier and he'd cut it for you in a few minutes for a few bucks, but he wouldn't guarantee success when cutting old glass.
Prepare for some failed attempts if you're tackling it yourself, but as you say, it's all over the place at every council clean up, and I've got a bit of stock under the house if I need any.

Quote:

---

Originally Posted by ozwinner

Gooder?

---

Quote:

---

Originally Posted by watson

Indubitably!

---

That's most cromulent terminology you're using there guys.

I used to cut the stuff for a living. Here's a previous post on it:

http://www.woodworkforums.ubeaut.com...ead.php?t=7326

FWIW We didn't rate the diamond cutters very highly. We tried one but always went back to the wheeled cutter. Might have been a knack thing but you stick to what you're used to I suppose.