KVM - Sit Stand Desktop

KVM - Sit Stand Desktop

My latest project. A prototype.
Made from scraps and left over pieces from bundle project purchases and previous purchases.
So it was all in the work shop just waiting for my use.

The gorgeous lady was talking about a sit/stand desk top.
I had a look and they are so expensive.
Thought I'd have a go.

Stumbled onto an instructable for a simple light weight notebook sit stand desk here:
Convertible Standing/Sitting Desk for $200
Make this look easy.

So took the basic design and beefed it up for my iMac.
Can't have it dropping.
And wanted a stable work platform without flex or shaking.

We have some very nice matching desks
so changed the design to a sit stand desktop.

Attachment 401748

Sitting Position
Attachment 401734

Standing Position
Attachment 401735

Bunnings outdoor blinds accessories for the thick rope
https://www.bunnings.com.au/smart-ho...-cord_p1281597

And shade cloth accessories for the pulleys and tie downs.
https://www.bunnings.com.au/coolaroo...d-kit_p3301518

Attachment 401736 Attachment 401737 Attachment 401738

50 x 50 Hard wood battens.
They were silver grey.
I tried to skin the grey off them a bit and straighten them with the table saw as I didn't have a thicknesses.
The wood was so hard and the blade was so gummed up they kept sticking.
36" for $1 each for a pack of 25.
Attachment 401739 Attachment 401740 Attachment 401741



Glued, Screwed and pocket hole joined.
Solid as.
Attachment 401765


Drawer runners off eBay for $10 a pair.
Wasn't working until I make a solid square instead of an open ended U shape to attach them to.
One fast spray of WD40 and much better.
the slow close mechanisms are tight so no latches needed to keep in place.
Might be the quality of the slides but more than likely my inexperience as using them.
Attachment 401742 Attachment 401743

The keyboard support had to be from 6mm as I didn't want it any higher than it already was.
Which needed a bit of support on the very ends.
Lucky the diagonal supports act as handles to lift the work area.
Regrettably its so heavy I have to step around the back to lift the counter weight to lower the work area.
No big deal.

I've had another test I just need to apply more pressure properly on the diagonal support to get it to come down.
Now that I'm thinking about this as I type it,
I'm wondering if I removed one of the brick counter weights if it would be easier.
Anyway a work in progress.
Yes! That was it. Too easy.


Attachment 401744 Attachment 401745 Attachment 401746

Even though I told the good lady it was just a prototype and I could paint it black,
the lady doesn't like it at all.
As it doesn't go with our nice matching office furniture.
She says it looks like it should be in the work shed.
I think I'll give it to her as a Chrissie Prezzie! LOL

Attachment 401748

Surprising I had designed the lift for 13"
Which is the top of the desk to my standing elbow.
And it came out perfectly 13"

Sounds like a good idea. How far along is yours? Do we have some pics to come?

DaveTTC

Turning Wood into Art

You're quick!

Yes, If I don't post/save often I loose my post.
I'ts stuck trying to upload pics grrrr.
Lost them. Oh well. I'll have to start over.

Looks good. Have you considered some kind of gas strut or piston to slow the drop in case of cord breaking?

I like the concept

Dave TTC
Turning Wood Into Art

Thanks for the interest.
No.
That cord is thick and strong.
And the slides are hard to move and the slow close helps.
I can install some latches on either side to keep the work area from dropping.
I've also been thinking about something to lock the monitor base down to the work area.

http://uploads.tapatalk-cdn.com/2016...5bc2beb19b.jpg

Horizontal starting
accross the Original bundled hard wood.
Middle and verticle piece on the right: after a number of micro passes on the table saw with a gummed up blade.
Bottom: single pass on a jointer

Although the lady NOW says the original might be what some people want
and that the middle has some interesting features.
LOL
I'll be building the next version from the jointer results.

No thicknesser.
So wondering if running all four sides thru the jointer would be good enough.

I've been working with "the dark side" timbers for quite some time.
This lighter timber I find quite attractive.
Thanks Ian (Forum member:aarggh!)




Sent from my iPhone using Tapatalk

You can dress all sides on a jointer. If you want relatively parallel this will be a challenge.

It may mean dropping one side onto the exit table and then doing a pass to take more off one side to bring into parallel or tweaking with a hand plane.

If you are not after actual perfection but simply for it to look good to the eye and slight differenced at joints can be made good with sanding

Dave TTC
Turning Wood Into Art

some came out fine.
Others wonkie.

Oh well.
Thicknesser search.

v2
Attachment 404001 Attachment 404002

All good mate. Never too late for a like and positive post.

At the time I needed a project and have been wanting a standing desk for a while.
The prices at the time for one off the shelf were ridiculous. $500+
It all worked out well.

I have to really force myself to actually use it and stand at it.
But once I get used to standing again it's easy.
It's much better using a standing mat as well.